oily water seperator (ows) maintenance tips

By Creations -
oily water seperator (ows) maintenance tips.


Every engineer on ship knows the importance of oily water separator (OWS) and must have heard stories of legal actions taken against seafarers who tried to fiddle or bypass the automation system of the OWS.
The most common cause of people tempering with oily water separator is deterioration of performance of the system.
Apart from the filter getting clogged due to continuous usage, there can be many other reasons for the lack of performance.
A few critical points, which are often ignored and less commonly known to engineers operating oily water separator on daily basis, are discussed in this article to ensure efficient performance of oily water separator (coalesce filter type) used onboard ships:

1. Oil In Bilge: The separator is suitable for separating small quantity of oil in bilge and not the other way round. If there is a mixture consisting of small quantity of water in oil, better not to pass it though the OWS and directly transfer it to waste oil tank for sludge disposal to shore or for incineration.
2. Keep Viscosity in Limit: Highly viscous oil if supplied for oily water separation will clog the filter. It is important to keep the viscosity of the oil within 1000 mm2/s
3. Discharge Outside Separator: Never discharge or drain water oil mixture from the separator abruptly out of OWS as it will lead to the separated oil adhere to coalescers, making it inoperative. Ensure to discharge the collected separated oil outside the separator and clean the internals of the OWS by supplying water.
4. Install Dust Filter: While using OWS for discharging bilge mixture containing dust and sand (a coarse grained entity), it will be difficult for the coalescer filter to pass dust and sand due to their sizes. This will reduce the operating hours of the filter and in-turn the efficiency of the OWS. The ideal service life of the filter normally ranges from 1-2 year depending upon the manufacturing process, considering daily operation of one hour. It is advisable to install a dust filter in the inlet line of the OWS to avoid this trouble.
5. Exchanging Probe for Fault Finding: for In most of the 15ppm OWS models, the oil level detecting probe and transmitting convertor in the 1st and 2nd stage chamber are identical. In the event of trouble, exchange these with each other, between the chambers, as this will help in finding out the source of trouble quickly.
6. Keep Check On Heating Device: If a heating device is provided, ensure it is ON when OWS is in operation and switched OFF before OWS is stopped. In case when the OWS is run for a long time, keep a track on the heater for overheating of coils. If the separator is overheated to high extent, there may be some production of inflammable gases inside.
7. Protect Internal Coating: The OWS internals are applied with tar epoxy coating, which is inflammable. Avoid bringing fire near to it or perform welding over the surface or body as the heat generated will damage the coating, making OWS susceptible to corrosion
8. Check Water Level: Ensure that the separator is initially filled with sea water before bilge mixture is supplied to it. This is to increase the life of filters and also to maintain the operational efficiency of the separator
9. Prevent Leakage: Ensure the means provided to avoid leaking or flowing out of water due to siphon effect. Failure to do so will allow oil to flow in the secondary chamber highly affecting the treatment capability of the machine and clogging the 2nd stage filters
10. Check Effluent: Frequent checks on effluent to be done to assess the performance of the separator. If the effluent is found contaminated, immediately stop the separator and take preventive actions
The operator of OWS should be thorough about the system, design, piping arrangement and of course the operating procedure of oily water separator. Out of all the machinery systems, OWS is kept at high priority due to stringent rules and regulations attached to it for ensuring environmental compliance. Hence it is important for the ship staff to maintain this machine in best of its shape.
Over to you..
Do you know any OWS maintenance tips that should be added to the list?

Let’s know in the comments below.

Comments

Post a Comment

Popular posts from this blog

How High Pressure Water Mist Fire Fighting System For Ships Works?

By Creations -
Image
How High Pressure Water Mist Fire Fighting System For Ships Works? check out and watch this video from youtube to understand easily click this link to redirect to youtube https://youtu.be/KFZKHfsxntg The hyper mist or high pressure fog fire fighting system is installed for all important ship’s machinery systems in the engine room (ME. AE, Purifier, Boiler etc.). The high-pressure water mist/fog system provides water mist protection during emergencies to engine room areas and machinery spaces. This system is independent of any other fixed fire fighting system such as foam or CO2 system. Following are the most common areas covered by water mist system: Incinerator room Auxiliary boiler room Auxiliary generators Main engine cylinder head platform Purifier room Inert gas generator room Steering gear room A fresh water pump takes suction from fresh water tank to supply high-pressure water to the sprinkler system. Each area is isolated by valves, w...
Read more

How is Power Generated and Supplied on a Ship?

By Creations -
How is Power Generated and Supplied on a Ship? A ship is like a floating city with all the privileges enjoyed by any normal land city. Just like a conventional city, the ship also requires all the basic amenities to sustain life on board; the chief among them is power or electricity. In this article we will learn as to how power is generated and supplied on board a ship. Power generation On board Shipboard power is generated using a prime mover and an alternator working together. For this an alternating current generator is used on board. The generator works on the principle that when a magnetic field around a conductor varies, a current is induced in the conductor. The generator consists of a stationary set of conductors wound in coils on an iron core. This is known as the stator. A rotating magnet called the rotor turns inside this stator producing magnetic field. This field cuts across the conductor, generating an induced EMF or electro-magnetic force as the mechanical in...
Read more