Air Compressor Problems Marine Engineers Must Know

By Creations -

Air Compressor Problems Marine Engineers Must Know

An air compressor is an important machinery in the ship’s engine room which supports several other systems, including the main engine. However, compressor is one machine which require constant monitoring and maintenance in order to ensure its runs smoothly. Though a number of safety devices are provided on the compressor, it is only prudent to take all the necessary precautions that are require for smooth running of the compressor.
For understanding common problems with air compressors, it is important to know all the different parts of the system. One must also know all important checks that are required to be made before operating the compressor. As a marine engineer working on ships, you should be able to understand and troubleshoot some of the common problems associated with the marine air compressor. Mentioned below are five such common problems.
1. Compressor Capacity is Low:
This is one of the most common problems seen on all types of ships. Often, compressor capacity can go low or reduced if it is running for long time and eventually it is unable to cope up with the air demand.
Main reasons for this problem are:
  • Leakage in discharge and suction valves
  • Fault or leakage in the unloader
  • Leakage from relief valve
  • Increase in bumping clearance
  • Wrong setting of compressor auto cut-in and cut-out (too close)
2. Oil Carry Over in Air:
If the compressed air in the system is carrying oil, would be mainly because of the following reasons :
  • Oil separator is not working correctly hence oil is being carried to the air receiver
  • The cylinder lubrication is adjusted at high quantity, leading to carry over of oil with air
  • The auto drain is malfunctioning
3. Excessive Vibration and Noise:
If the compressor is generating too much of noise and vibration, it can be because of the following reasons:
  • Loose pulley, flywheel, belt, belt guard, cooler, clamps or accessories
  • Lack of oil in the crankcase
  • Piston hitting the valve plate i.e reduced bumping clearance
  • Compressor holding down bolts are loose
  • Compressor foundation chocks worn out
4. Overheating of Discharged Air
If the temperature of the discharged compressed air is high, it can be because of overheating caused as a result of the following reasons:
  • Chocked or dirty intercooler tube
  • Cooling water pump capacity decreased or insufficient
  • The atmosphere at air suction of compressor is hot
  • No forced ventilation for fresh air near compressor
  • Damage in the head gasket
  • Chocked air suction filter
  • Valves of 1st or 2nd stage leaking
5.Milky Oil in the Crankcase
If there is a accumulation of milky colored oil in the crankcase, it can be because of the following reasons:
  • Water leakage from cylinder liner
  • Water leakage form jacket
  • Oil running hour is over
These are some of the most common problems that are found in continuously running air compressors on board ships.

Comments

Post a Comment

Popular posts from this blog

Extremely Important Points For Windlass Maintenance On Ships

By Creations -
Extremely Important Points For Windlass Maintenance On Ships Most of the windlasses found onboard ships these days are driven directly by electric motors or by pressurised hydraulic oil. They cater to hoisting up varying loads with the help of gear and teeth arrangement. The major parts of a windlass are main shaft, driving shaft, inspection cover, gear, gear frame, drums (one or more), warping head or couplings, brake band, brake liner assembly, chain wheel, gear wheel, pinion, clutch and high speed low speed hydraulic valve blocks. Regular inspection of external and moving parts of gear and shaft enables a ship’s officer to judge the wear and amount of use of this important machinery.While using windlass for hoisting, an early indication can be temperature rise on the exterior of hydraulic pipe lines driving the main shaft. This further needs to be investigated for the correct technical specification and properties of the oil used and load ...
Read more

How to Perform Ship’s Stern Tube Integrity Test in The Dry Dock?

By Creations -
Image
How to Perform Ship’s Stern Tube Integrity Test in The Dry Dock? The intention behind sending a ship to the dry dock at regular intervals of time is to inspect those parts which are technically difficult to access when the ship is at sea. One of the systems that is inspected during dry docking is the ship’s stern tube system, which carries the propeller shaft turned by the engine’s intermediate shaft, a configuration that propels the ship in the desired direction. During dry dock, the stern tube is opened up for inspection of the seals, the stern cylinder, and the shaft. Overhauling and replacement of seals are done if their condition is not as per maker’s desire. After overhauling and boxing back the stern tube system, the next step is to make sure that it does not leak oil out to the sea or water inside the engine room, once the ship is water bourn. For this purpose, post overhauling inspections are carried out in the dry dock by experience ma...
Read more

How High Pressure Water Mist Fire Fighting System For Ships Works?

By Creations -
Image
How High Pressure Water Mist Fire Fighting System For Ships Works? check out and watch this video from youtube to understand easily click this link to redirect to youtube https://youtu.be/KFZKHfsxntg The hyper mist or high pressure fog fire fighting system is installed for all important ship’s machinery systems in the engine room (ME. AE, Purifier, Boiler etc.). The high-pressure water mist/fog system provides water mist protection during emergencies to engine room areas and machinery spaces. This system is independent of any other fixed fire fighting system such as foam or CO2 system. Following are the most common areas covered by water mist system: Incinerator room Auxiliary boiler room Auxiliary generators Main engine cylinder head platform Purifier room Inert gas generator room Steering gear room A fresh water pump takes suction from fresh water tank to supply high-pressure water to the sprinkler system. Each area is isolated by valves, w...
Read more